Here you can search our online database of IDDRG papers using various search profiles (e.g. author(s)’name, Papers’ title, etc.). Papers are available online only since 2005. If you need old paper please go to IDDRG Library Archives where you will find information how to get these papers in paper format.
| Title | |||
|---|---|---|---|
|
New criterion describing combined effects of lode angle and sign of pressure on yielding and void evolution |
J.L. Alves, O. Cazacu, B. Revil-Baudard | 2013 | Download |
|
Prediction of localized necking for nonlinear strain paths using the MMFC and the HAH model |
N. Manopulo, P. Peters, P. Hora | 2013 | Download |
|
Numerical investigation of small curvature bendability of high strength low alloyed steel in air and die bending processes |
I. Tsoupis, S. Hildering, M. Merklein | 2013 | Download |
|
Estimation of the limit hole expansion ratio affected by pre-strain produced during hole piercing process to make test specimen |
K. Ito, N. Mori, T. Imanaga, M. Narita | 2013 | Download |
|
Development of crack prediction method considering bendability of Ultra-High Strength Steel sheets |
Y. Fujii, T. Shinmiya, K. Higai, Y. Yamasaki, T. Inazumi | 2013 | Download |
|
Comparison between the Lemaitre and a modified Lemaitre damage model on sheet steel blanking |
B.-A. Behrens, A. Bouguecha, I. Peshekhodov, C. Bonk | 2013 | Download |
|
Optimization of the cutting edge geometry for single staged trimming with high cutting angles |
M. Bednarz, A. Lipp, C. Sunderkötter, T. Hallfeldt, M. Grün | 2013 | Download |
|
Influence of the sheared edge condition on the hole expansion of dual phase steel |
N. Pathak, C. Butcher, M. Worswick | 2013 | Download |
|
Experimental investigation of the influence of shear cutting parameters on the edge crack sensitivity of dual phase steels |
M. Liewald, M. Gall | 2013 | Download |
|
Multiscale simulation of ductile damage of dual-phase steels |
J. Lian, S. Münstermann, W. Bleck | 2013 | Download |
|
Multimodality characterization of burr edge in sheet blanking |
S. Kumar, K. Narasimhan, A. Tewari, V. Hiwarkar | 2013 | Download |
|
Failure prediction methods in 3D ale fine blanking simulations |
T. Wesner, N. Manopulo, P. Hora | 2013 | Download |
|
Simulation based method of surface deflect detection |
T. Schönbach, M. Avermann | 2013 | Download |
|
Air bent safety components for the carbody |
C. Gasser, R. Kolleck | 2013 | Download |
|
How to enable a process planner to take better and transparent decisions |
S. Wagner | 2013 | Download |
|
Analysis method to identify cause of springback in press forming |
M. Urabe, A. Ishiwatari, H. Kano, J. Hiramoto, T. Inazumi | 2013 | Download |
|
Time-dependent residual stress and geometry analysis of UHSS deep drawn components |
B. Wadman, P. Ottosson, J. Holmberg, L.-O. Ingemarsson, E.Sagström | 2013 | Download |
|
Influence of used yield function in deep drawing simulation of highly anisotropic aluminum alloy |
J. Nový, V. Vaché, J. Sobotka | 2013 | Download |
|
Prediction of phase fractions and Vickers hardness in hot stamping processes with an advanced material model in LS-DYNA |
B. Hochholdinger, D. Lorenz, T. Erhart, M. Schill | 2013 | Download |
|
A new design of electro-magnetic actuator for electro-magnetic deep drawing (EMDD) of axisymmetric shells |
M. Singhal, P.P. Date | 2013 | Download |